I-80 Chain Controls & Live Cameras: Sacramento to Donner Summit
The direct answer: below is the current Caltrans chain control status on I-80 in each direction and six live video cameras from Watt Avenue in North Highlands to the Truckee scales. For heavy trucks the rule is simple: when I-80 is posted R-1 or higher, trucks over 6,500 lb need chains mounted to continue over Donner Summit.
Live I-80 conditions: Sacramento to Donner Summit
Caltrans data · checked Nov 18, 5:08 PM PT
Eastbound — toward Truckee and Reno
R-2 chain control
Alta to Boca
- Trucks: chains mounted to proceed — maximum truck chain requirement over Donner Summit.
- Truck-trailer combinations turned around at Applegate (traction problems over the summit).
Westbound — toward Sacramento
R-2 chain control
Alta to Truckee
- Trucks: chains mounted to proceed — maximum truck chain requirement over Donner Summit.
- Truck-trailer combinations turned around at CA / NV Stateline - Gold Ranch (traction problems over the summit).
Live Caltrans video. Tap a camera to enlarge. The state runs these feeds and they can drop out; a dropped feed shows the latest still image.
Chains are up on I-80. Truck trouble on the way to the summit, or something you want checked before you climb? Call a mechanic, not a call center.
Call (916) 571-8888Winter truck prep for I-80 →I-80 fleet service →What R-1, R-2 and R-3 mean for trucks →
Source: Caltrans District 3 chain control and CCTV feeds. Conditions change fast — confirm with QuickMap or 1-800-427-7623 before you travel.
What the chain control codes mean for trucks
Meanings are Caltrans' own wording from the chain control feed. Sources: Caltrans chain controls · Caltrans truck chain requirements.
| Code | What Caltrans says | For a semi |
|---|---|---|
| R-0 | No chain controls are in effect. | No chain requirement. |
| R-1 | Chains required on all vehicles except passenger vehicles and light-duty trucks under 6,000 lb with snow tires on at least two drive wheels. Vehicles towing trailers must have chains on one drive axle. | Heavy trucks chain up. |
| R-2 | Chains or traction devices required on all vehicles except four-wheel / all-wheel drive vehicles with snow-tread tires on all four wheels. | Heavy trucks chain up. |
| R-3 | Chains required on all vehicles, no exceptions. The highway is often closed before R-3 is imposed. | Heavy trucks chain up. |
| RC | Closed to traffic. | No travel. |
| MIN / MAX | Truck chain requirement is minimum (or maximum) for all trucks using Donner Summit. | Follow the posted placement chart. |
| Chain check (TS) | All trucks must stop at the chain checkpoint. Drivers must have maximum chains in their possession to proceed; trucks without chains are turned around. Permit loads are prohibited over the summit. | Carry a full maximum set. |
| Turnaround (TTA) | All truck-trailer combinations are turned around at the chain control because of traction problems over Donner Summit. | Combinations wait. |
Before the climb
Trucks that get stranded at Donner usually fail on the same short list: brakes and slack adjusters, moisture in the air system, DEF, batteries and chains that do not fit. The full checklist is in our winter truck prep guide for I-80, and the scales along the route are in weigh stations near Sacramento. Fleets that run the corridor every week can see I-80 fleet service. If a truck is already down, read mobile repair or tow? and call (916) 571-8888.
Common questions
Do semi trucks have to put on chains at R-1?
Yes. R-1 only exempts passenger vehicles and light-duty trucks under 6,000 lb with snow tires. When a California highway is posted for chains, heavy-duty vehicles over 6,500 lb gross weight must have chains mounted to proceed, per Caltrans truck chain requirements.
What do MIN and MAX mean on Donner Summit?
They are the truck chain requirement Caltrans is enforcing for all trucks using Donner Summit: minimum or maximum chains. How many tires must be chained under each is set by the Caltrans chain placement chart. At a chain check, trucks must carry a full maximum set to continue.
Are automatic traction devices legal instead of chains?
Caltrans accepts automatic traction devices as a one-for-one replacement for conventional chains, but a truck with only ATDs may still have to add chains on outside wheels to meet the placement chart.
How current is this page?
Chain control status comes from Caltrans' District 3 feed and is refreshed about every five minutes. The cameras are live Caltrans video; when a feed drops, the tile shows the latest still image, which updates about once a minute. Conditions change fast, so confirm on Caltrans QuickMap or at 1-800-427-7623 before you travel.
My truck has a problem before the climb. What should I do?
Call (916) 571-8888. The shop is in North Highlands off I-80, and a mechanic will tell you whether it is a mobile repair, a drive-in repair, or a tow. Brakes, the air system, DEF and chains are what strand trucks on the pass, and they are worth checking before winter.
Live conditions: Caltrans QuickMap · Caltrans highway information line 1-800-427-7623.
Talk to us about your fleet
Tell us what you run and what's been eating your uptime. We'll review it and talk through what a maintenance rhythm with one shop would look like — honestly, including whether we're the right fit.
